I don't have any pics but,the front band is essentially the same procedure. I personally like using a beam type wrench so that I can see it coming up on it's final torque, and I also back off the torque values by 10% since it's a worn in band- right or wrong that's my opinion only. It's much better to err on the loose side band adjustments, too tight is probably gonna break some parts. Then after you tighten the locknut, this mark also gives you a positive verification that it hasn't turned, as you tightened it. Here's a couple of tips, use the paint marker on the adjuster to make a reference mark, AFTER you've reached your final torque.Then carefully take note of it's location and back it off the 3 turns. Get yourself a 1/4" torque wrench and 5.5mm socket.Tighten the band to 72 INCH lbs then back off 3 full turns ,hold the adjuster (very important) so it doesn't turn as you tighten the locknut-25ft lbs. That being said, crack loose the lock nut, and back it off 4-5 turns so it doesn't bottom out as you tighten the band. It should go in easily, if you have to force it stop and verify everything's all lined up, before you go primal on it torque all the fasteners, hook up the connectors and your done! Eezy peezy.Ħ) Now's the time to adjust the rear band, it's a easy job but it has to be done right,if you don't do it properly, bad (expensive) things are probably coming your way. If you notice, there is a slot in the retainer that indexes to a groove in the transducer also, thats to hold it in after reassemblyĥ) Slide the transducer into the spacer after coating the o-rings with some ATF, make sure that it's turned so that the slot will line up properly with the retainer ,oil the o-rings on the solenoid and slide it into the slot in the retainer.Hold it in the bracket ,and reinstall the opposite of how you removed it,just make sure the retainer is lining up with the slot in the transducer as you guide it in. The transducer will remain, just make a note of it's orientation and then pull it out as well. ![]() ![]() ![]() I'd recommend putting a drain plug in the pan while it's off ,to make draining the fluid easier.Ģ)Pic of the Solenoid and transducer, I used the Borg-Warner 50185 Solenoid upgrade instead of the OEM, recommended because of it's larger magnet, and the difference in my shifts is amazing.ģ)Remove the filter and there they are, your going to need a torx bit-T40 I believe and socket to drop it out, but first you'll need unplug the the electrical connectors to the solenoid and transducer, go easy with them ,the hot cold cycles tend to make them brittle.Ĥ)I removed the two torx screws and bolts, leaving the bolt closest to the rear band adjuster in, this will hold the base on the valve body,no risk of gasket damage doing it this way.At this point you can pull gently on the stamped retainer and the governor solenoid will pop out of the base,since its held in a slot in the retainer. The idea is to get the pan to drop on only one side to minimize spilling and dump the fluid off a corner- easier said than done. ![]() solenoid and transducer,1/4' drive torque wrench, 1/4" & 3/8" socket sets, basic metric wrench set, a pick or small screwdriver, a drill with a 1/2" bit for the drain plug kit, big catch pan:thumbup2:, and a paint pen or sharpie,plus whatever I forgot:ashamed:ġ) Drop pan to drain the fluid, the easiest way is to go around and loosen them all just a turn, then work from one side loosen the bolts in steps. I took some pics as I did mine last week, and thought I'd try making a write up on it.īasic tools etc.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |